PowerView® Curtain Track Transceiver¶
1. Mounting the Forest Curtain Track¶
The PowerView® CT Transceiver dongle is suited to be used with the Forest Shuttle® system.
1.1 Installation of the track¶
Assemble the track (according Forest instructions.)
Install the brackets to the wall or ceiling and fix the track onto the brackets.
Do not attach curtains until after end positions have been set or complete installation is finished
- Position the master carrier(s) into the half open position.
Attach Forest Shuttle motor to the track.
- Position motor-drive-head into the track-gear.
1.2 Connecting power and communication¶
Connect the AC or DC power plug to the Forest Shuttle® motor power socket. (Do not plug into the wall socket)
Mount Transceiver dongle to the side of the track motor
Connect data cable between PowerView® Transceiver and Forest Shuttle® motor (Input: Com Port2)
Connect the AC plug of Forest power supply to the wall socket.
2. Programming the Curtain track¶
2.1 Setting and adjusting end limits of the Shuttle® motor¶
After power up of the Shuttle® motor the open and close positions are to be referenced by the Shuttle® S/L/M motor receiver.
Before starting the programming-proces, make sure the track master carrier(s) are in the open position.
Setting the motor direction and close limit By pulling the master carrier towards the closed position the motor direction is automatically detected. The master carrier will automatically travel towards the closed end position.
Setting the open limit when the closed position is reached that end limit is set. to set the open limit pull the master carrier towards the open position. the carrier will automatically travel towards the fully open position and the open end limit will be set accordingly.
Stack Back Upon reaching the fully open position the carrier will stop (yellow LED4 is on. see step 2.2.4 ). Now the stack back position can be adjusted by hand. When the master carrier is not moved for 10 seconds the LED4 will turn off indicating the open limit has been set.
2.2 Re-adjusting the End limit positions¶
When needed, (e.g. adding extra carriers) the end positions can be changed. To do so, please follow the next steps.
Move the curtain to the open position
Press Button 4x with a pen or other pointy object
LED moves from 1st > 2nd > 3rd> 4th LED
Keep Button pressed for 5 sec.
Yellow LED4 blinks and goes off
End positions have now been cleared
Press / pull curtain towards close position, curtain will close automatically
Press / pull curtain towards open position, curtain will open automatically
Directly after stopping of the motor (at open position) the yellow LED(4) will light up. the open position can be adjusted to the desired position.
Wait until the yellow LED goes off, End positions are now stored into the memory of the motor.
2.3 Forest shuttle® configuration options¶
Additionaly to the above the Forest Shuttle® has the below configuration options. The configuration button and LED's can be located at the bottom of the curtain track motor.
Use a pin or pen to change settings in the configuration menu. Choose the setting you want to change (table below) and press the button that many times (corresponding with setting).LED's will cycle to indicate the amount of times pressed.
# of Presses
Speed low (14cm/s)
Speed High (17cm/s)
Reset End limits / adjust open limit
Touch impulse sensitivity high
Touch impulse sensitivity low
Touch impulse sensitivity off
Factory setting reset
Confirm the desired setting by pressing the button for 5 seconds until the led blinks 3 times and goes OFF.
3. Pairing the Powerview® Remote to the Powerview® CT Transceiver¶
Adding the PV Transceiver CT to a remote can be done using the normal procedure for adding a shade to a remote. See Quickstart guide adding a shade to a remote
A Remote can control 6 groups of shades (which are the buttons 1 to 6). The instructions below assign a shade to group 1. Depending on your preference you can choose your own group.
This instruction will make use of the following buttons on the Remote:
Transceiver button on your curtain track transceiver dongle.
stop for 6 seconds.
Keep pressing until the remote lights start blinking.
This will activate the group 1 on the remote.
Press and hold the
You will see the curtain move shortly.
If your remote is still flashing Press
stop for 6 seconds.
Keep pressing until the flashing stops.
4. Transceiver dongle control button LED¶
The motor control button LED gives an indication of the motor status. The LED can flash RED, ORANGE or GREEN. Below is the overview of all possible combinations.
(Repetition of signalling sequence in a loop). No correct communication to FOREST shuttle. Please check if PV Transceiver is connected correctly to PORT 2 AUX of shuttle motor
(Repetition of signalling sequence in a loop) PV Transceiver is connected correctly but FOREST shuttle is not referenced. Please set shuttle end limits as described at chapter setting end limits
PV Transceiver is connected correctly and is ready for operation
5. Additional technical notes¶
PV Transceiver behaviour after a power disconnection: A recalibration run for the forest shuttle is required after a power failure. Shuttle recalibration run starts automatically and always in close direction after first user operation command (manually or by PV command and regardless of selected operating direction). Recalibration run cannot be interrupted even with STOP command.
Hunter Douglas Europe B.V. and its affiliates (Hunter Douglas) reserve the right to make corrections, enhancements, improvements and other changes to its products and services, and to discontinue any product or service. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products (also referred to herein as "components") are sold subject to Hunter Douglas’ terms and conditions of sale supplied at the time of order acknowledgment. Hunter Douglas warrants performance of its components to the specifications applicable at the time of sale, in accordance with its standard warranty terms. Testing and other quality control techniques are used to the extent Hunter Douglas deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. Hunter Douglas assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products, applications and interfaces using Hunter Douglas components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. Hunter Douglas does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which Hunter Douglas components or services are used. Information published by Hunter Douglas regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from Hunter Douglas under the patents or other intellectual property of Hunter Douglas. Reproduction of Hunter Douglas information in Hunter Douglas data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Hunter Douglas is not responsible or liable for any altered documentation. Information of third parties may be subject to additional restrictions. Resale of Hunter Douglas components or services with statements different from or beyond the parameters stated by Hunter Douglas for that component or service voids all express and any implied warranties for the associated Hunter Douglas component or service and is an unfair and deceptive business practice. Hunter Douglas is not responsible or liable for any such statements. Buyers acknowledge and agree that they are solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of Hunter Douglas components in its applications, notwithstanding any applications-related information or support that may be provided by Hunter Douglas. Buyers represent and agree that they have all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyers fully indemnify Hunter Douglas and its representatives against any damages arising out of the use of any Hunter Douglas components in safety-critical applications.
document version: 1.0 | generated: 2019-08-18 23:30:40