(Material) Safety Data Sheet (SDS/MSDS)¶
according to 1907/2006/EC, Article 31
**Issue date: 13-10-2018
Revision no.: 1
Revision date 12-10-2018
The information contained within is provided as a service to our customers and for their information only. the information and recomendations set forth herein are made in good faith and are believed to be accurate as of date of preparation or revision. Hunter Douglas makes no warranty expressed or implied, and disclaims all liabilities from reliance on it.
Section 1 - Identification¶
Product Name and description
Trade name: Lithium ion Battery / Lithium ion battery pack
Model: 4S1P 18650 model battery pack containing BMS protection circuitry with capacity less than or equal to 3Ahr
Nominal Voltage: 14.4V or 14.8V
Supplier & Manufacturer
Hunter Douglas Europe B.V.
Shengzhou BAK Battery Co., Ltd.
LiuQiao Village, Zheng An town, Zhongmou county
3071 EL Rotterdam
Zhengzhou city Henan 451450,
Telephone: +31-10-486 9911
Section 2 - Hazards Identification¶
Classification of the substance or mixture
Classification according to Regulation (EC) No 1272/2008
In accordance with article 3 (3) of REACH, this / these item(s) are articles. An article is not subject to the mandatory marking regulations applicable to dangerous substances.
The product is not classified as hazardous to health or environment according to the CLP regulation.
Lithium ion cells are not hazardous when used according to the instructions of the manufacturer under normal conditions.
In case of abuse, there is a risk of rupture, fire, heat, or leakage of internal components which could release hazardous materials.
Section 3 - Composition/Information on Ingredients(1)¶
Lithium transition metal oxide(2,3)
(1) Not every product contains all of these materials
(2) M means a combination of Co, Ni or Mn. This component may consist of a mixture of compounds, each of which may contain these elements.
(3) Mixted materials like Lithium transition metal oxide and Electrolyte Do not have CAS No.
Section 4 - First-aid Measures¶
Lithium ion cells are not hazardous under normal circumstances. In case of fire or rupture, the leakage of internal hazardous substance and formation of hazardous substance may occur, the following measures should be taken in case of contact with these:
Eyes: Check for and remove any contact lenses. Immediately flush with plenty of clean water for at least 15 minutes, seek medical assistance.
Skin: Immediately flush with plenty of clean water for 15 minutes; seek medical assistance if reaction is severe.
Inhalation: Expose the person to fresh air immediately, use respitory device if necessary.Seek medical assistance, and ventilate the contaminated area.
Ingestion: Rinse mouth with clean water immediately. Make the victim vomit and seek medical assistance.
Section 5 - Fire-Fighting Measures¶
Combustion products and decomposition products include: carbon monoxide, carbon dioxide, hydrogen
fluoride, phosphorus fluoride.
- Dry chemical or water type extinguishers are most effective means to extinguish a battery fire.
- A carbon dioxide (C02) extinguisher is also effective
- cover with sand or dry earth.
Special fire fighting procedures:
- Respiratory protection: in all fire situations, wear self-contained breathing apparatus (SCBA) and Chemical apron.
- Skin protection: Wear Full fire fighting protective clothing and equipment to prevvent body contact with electrolyte solution
- Eye protection: Safety glasses are recommended.
During water application caution is advised as burning pieces of flammable particles may be ejected from the fire.
Causes of unuasual fire or explosion hazard: Batteries that are damaged, opened or expxosed to excessive heat/fire may flame or leak potentially hazardous organic vapors. Combustion products and decomposition products include: carbon monoxide, carbon dioxide, hydrogen fluoride, phosphorus fluoride.
Section 6 - Accidental Release Measures¶
Under normal condition of use, a battery is hermetically sealed and not hazardous. Leakage or release of hazardous materials contained within a battery would be possible under abbusive conditions.
When leakage of cells happens, liquid could be absorbed with sands, earth or other inert substance, and the contaminated area should be ventilated. Always use protective clothing and equipment when handling damaged batteries.
Section 7 - Handling and storage¶
Do not short positive and negative terminals by contact with conductors. Do not overheat or incinerate. Do not open/disassemble, puncture, crush or deform battery or cells. Do not bypass any safety circuitry.
Batteries are designed to be recharged. However improperly charging a battery may cause the product to flame or leak. use only appoved chargers and procedures.
Batteries should be seperated from other materials and stored in a non-combustible, well ventilated structure with sufficient clearance between walls and battery stacks.
Store and use away from heat, sparks, open flame, or any other ignition source. Store in a cool, dry environment (less than 35°C, less than 85% RH).
Long term storage temperature/humidity: -20°C~25°C / 0~90% RH (non condensing).
Section 8 - Exposure Controls/Personal Protection¶
There is no protection required under normal conditions. In case of leakage ventilation is required. Respirator, eye protection, protective gloves and protective clothes are required when dealing with fire and leakage.
Section 9 - Physical and Chemical Properties¶
Appearance: Cilindrical / cuboid;
Odor(4): Odorless, unless individual components exposed;
pH: Not applicable;
Flash point: Not applicable;
Flammability: Not applicable;
Vapor pressure: Not applicable;
Solubility (water)(1): Insoluble, unless individual components exposed;
Note(4): The following points are not applicable unless in case of leaking or damaged batteries with exposed internal components.
Section 10 - Stability and Reactivity¶
The batteries are stable under normal operating and storage conditions
Conditions to avoid:
Heat above 70° or incinerate. Deform. Mutilate. Crush. Pierce. Disassemble. Short circuit. Exposure to humid conditions over a long period.
Materials to avoid:
Water, strong Acid or Alkali solutions, oxidizing agents.
Hazardous decomposition products:
organic carbonate, hydrogen fluoride, carbon monoxide, carbon dioxide, phosphorus fluoride.
Section 11 - Toxicological Information¶
Batteries are not hazardous when used properly.
In case of fire or leakage combustion and decomposition products may cause irritation and toxicity to skin, eye and respiratory systems. Toxicity data of some substance is listed, Hydrogen fluoride:
Extremely toxic, May be fatal if inhaled or ingested. Readily absorbed through the skin contact may be fatal.
Possible mutagen. LCLO: 50 ppm/30m (human beings) LC50： 1276 ppm/1h （rats).
Carbon and graphite:
Slightly hazards in case of skin contact (irritant), ingestion, inhalation, which will cause chronic damage to upper respiratory tract and cardiovascular system.
Dust may cause respiratory irritation. LD50: 3.5 mg kg-1 (mouse).
Section 12 - Ecological Information¶
There is no influence on ecology or environment when used and disposed of properly (according local law).
Do not let internal components enter marine environment. Avoid releasing to water ways, waste water or ground water.
Section 13 - Disposal Considerations¶
Discarded cells should not be treated as ordinary trash. Recycling is recommended and is required by law. Requirements can vary on national, state/provincial and local bases.
Do not incinerate. Leaking or damaged batteries should be treated as chemical waste. Packaging is normally not contaminated by batteries.
Section 14 - Transport information¶
UN proper shipping name: ADR,IMO/IMDG,IATA
LITHIUM ION BATTERIES, LITHIUM ION BATTERIES CONTAINED IN OR PACKED WITH EQUIPMENT
Transport hazard class: ADR,IMO/IMDG,IATA
9 Miscellaneous dangerous substances and articles
Environmental hazards: Marine pollutant:
Special precautions for user
Warning: Miscellaneous dangerous substances and articles.
Transport in bulk according to Annex II of MARPOL and the IBC Code
Lithium-ion batteries are tested in accordance with: UN manual of Tests and Criteria, Part III, subsection 38.3
Packing instruction 965 Section IB applies to lithium ion batteries with a Watt-hour rating not exceeding 100 Wh packed in quantities that do not exceed the allowance permitted in Section II, Table 965-IB; (CAO Net quantity per package 10kg)
Road & Sea: ADR,IMO/IMDG
They meet the requirements of special provision SP188
Section 15 - Regulatory information¶
Safety, health and environmental regulations/legislation specific for the substance or mixture
- National regulations
- Other regulations, limitations and prohibitive regulations
- Substances of very high concern (SVHC) according to REACH, Article 57: None
Chemical safety assessment: not required
Section 16 - Other information¶
These data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
H228 Flammable solid.
H251 Self-heating: may catch fire.
H302 Harmful if swallowed.
H314 Causes severe skin burns and eye damage.
H317 May cause an allergic skin reaction.
H332 Harmful if inhaled.
H350i May cause cancer by inhalation.
H372 Causes damage to organs through prolonged or repeated exposure.
H400 Very toxic to aquatic life.
H410 Very toxic to aquatic life with long lasting effects.
H413 May cause long lasting harmful effects to aquatic life.
Department issuing data specification sheet:
Hunter Douglas Europe B.V.
Expert Center Motorisation & Control
3071 EL Rotterdam
T:+31 (0)10 486 9911 M: +31 (0)6 51 33 91 07
Email: infoMC@hde.nl / AW.Vos@hde.nl
Contact: Alex Vos
Hunter Douglas Europe B.V. and its affiliates (Hunter Douglas) reserve the right to make corrections, enhancements, improvements and other changes to its products and services, and to discontinue any product or service. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products (also referred to herein as "components") are sold subject to Hunter Douglas’ terms and conditions of sale supplied at the time of order acknowledgment. Hunter Douglas warrants performance of its components to the specifications applicable at the time of sale, in accordance with its standard warranty terms. Testing and other quality control techniques are used to the extent Hunter Douglas deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. Hunter Douglas assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products, applications and interfaces using Hunter Douglas components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. Hunter Douglas does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which Hunter Douglas components or services are used. Information published by Hunter Douglas regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from Hunter Douglas under the patents or other intellectual property of Hunter Douglas. Reproduction of Hunter Douglas information in Hunter Douglas data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Hunter Douglas is not responsible or liable for any altered documentation. Information of third parties may be subject to additional restrictions. Resale of Hunter Douglas components or services with statements different from or beyond the parameters stated by Hunter Douglas for that component or service voids all express and any implied warranties for the associated Hunter Douglas component or service and is an unfair and deceptive business practice. Hunter Douglas is not responsible or liable for any such statements. Buyers acknowledge and agree that they are solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of Hunter Douglas components in its applications, notwithstanding any applications-related information or support that may be provided by Hunter Douglas. Buyers represent and agree that they have all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyers fully indemnify Hunter Douglas and its representatives against any damages arising out of the use of any Hunter Douglas components in safety-critical applications. Manufacturer/Supplier address: Hunter Douglas Europe B.V, P.O. Box 5072 Piekstraat 2 3008 AB Rotterdam The Netherlands
document version: 1.0 | generated: 2021-10-14 23:12:04