Safety instructions
The motor may only be operated after reading these safety instructions, failing to do so might cause serious harm.
- Do not operate a blind which in any way is damaged
- Charging of battery operated blinds, only with suitable chargers
- only operate the blind within the prescribed environmental situation
- the motor may only be used in combination with the recommended and suitable power source, originally supplied with the blind.
- A remote control is considered NOT to be a children's toy
- window decoration motors should be replaced when the rated cycle limitation is reached




PowerView® PS-18/300 power supply¶
This guide will explain step-by-step how to install the PS-18/300 power supply and connect the PowerView® motor wires on the connection terminals. The following instruction will show you how to:
-
Install and mount the power supply on a wall
-
Correctly set up the wiring of the PowerView® installation
-
Connect the wires onto the terminal blocks of the power supply
1. Hardware overview¶
1.1. Package contents¶
PS-18/300 power supply
mounting template
8-pin terminal block (4pcs)
1.2. Optional accessories¶
power cable
(EU or UK version)
female jack adapter
1.3. Installation parts & equipment¶
To install the power supply and for connecting wires to the connection terminal block, following parts and equipment are needed.
Level
hammer drill
hammer
Set of screwdrivers
Pan head screws (4pcs)
wall plugs (4pcs)
2. Hardware installation¶
The PS-18/300 power supply has been designed to install vertically to a wall. An A4 paper template is available to easily determine the mounting holes.
Note
In this guide, the power supply will be installed on a concrete wall.
Before continuing, take note of the different connection terminals and components of the power supply.
IMPORTANT
- The ventilation holes (both sides of the housing) may not be covered. Leave enough free space of the left and right side.
- There are 4 fused motor group connection terminals. Each group is able to deliver max. 4Amps @ 18VDC.
Do not exceed the load on each terminal.
- In case of a broken group fuse, the group LED will not light up when the power supply is powered on.
- Always switch off the power supply and disconnect the power cable when installing or making connections.
- Make use of the cable management clamps to neatly align the motor and power cables.
- Make sure a power socket is nearby (max. 0.5m).
Note
The bare metal connections (18VDC) under the power supply's front cover are safe to touch when the power is on.
All 230VAC components are shielded from any possible human or pet contact.
2.1. Installing the power supply¶
2.1.1
Stick the mounting template onto the wall.
Use a level tool to align the template.
2.1.2
Drill 4 holes at the Pilot hole center
positons indicated on the template.
2.1.3
Remove the mounting template and use a hammer to put the wall plugs into place.
2.1.4
Use a screwdriver to install the screws.
The distance from the wall to the flat surface of the panhead screw is about 3.5mm.
2.1.5
Remove the front cover and mount the power supply to the wall.
2.2. Connecting cables¶
Remove the power supply from the wall and disconnect the power cable.
IMPORTANT
Make sure the power switch is set in the OFF
position.
There are different options on how-to connect a range of 18VDC PowerView® motors:
- Individually
- Daisy-chained
- Combination individually/daisy-chained
Note
As a general rule of thumb, connect maximum 4 motors
(1 motor = max. 1Amp power consumption) per terminal block.
Motors are connected individually
Motors are daisy-chained
Motors are connected individually and daisy-chained
Connecting a PowerView® motor to the power cable is done using a female jack adapter (article 17.0361.0000).
Motors are connected individually
Motors are daisy-chained
IMPORTANT
Depending on the motor count per chain and used wire surface/diameter, a maximum cable length per chain is allowed.
See table below for more information.
wire area: 0.5mm² | wire length [m.] | ||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | ||
# motors | 1 | 0.1 | 0.1 | 0.2 | 0.3 | 0.4 | 0.4 | 0.5 | 0.6 | 0.6 | 0.7 | 0.8 | 0.8 | 0.9 | 1 | 1.1 | 1.1 | 1.2 | 1.3 | 1.3 | 1.4 | 1.5 | 1.5 | 1.6 | 1.7 | 1.8 | 1.8 | 1.9 | 2 | 2 | 2.1 |
2 | 0.1 | 0.3 | 0.4 | 0.6 | 0.7 | 0.8 | 1 | 1.1 | 1.3 | 1.4 | 1.5 | 1.7 | 1.8 | 2 | 2.1 | 2.2 | 2.4 | 2.5 | 2.7 | 2.8 | 2.9 | 3.1 | 3.2 | 3.4 | 3.5 | 3.6 | 3.8 | 3.9 | 4.1 | 4.2 | |
3 | 0.2 | 0.4 | 0.6 | 0.8 | 1.1 | 1.3 | 1.5 | 1.7 | 1.9 | 2.1 | 2.3 | 2.5 | 2.7 | 2.9 | 3.2 | 3.4 | 3.6 | 3.8 | 4 | 4.2 | 4.4 | 4.6 | 4.8 | 5 | 5.3 | 5.5 | 5.7 | 5.9 | 6.1 | 6.3 | |
4 | 0.3 | 0.6 | 0.8 | 1.1 | 1.4 | 1.7 | 2 | 2.2 | 2.5 | 2.8 | 3.1 | 3.4 | 3.6 | 3.9 | 4.2 | 4.5 | 4.8 | 5 | 5.3 | 5.6 | 5.9 | 6.2 | 6.4 | 6.7 | 7 | 7.3 | 7.6 | 7.8 | 8.1 | 8.4 |
wire area: 0.75mm² | wire length [m.] | ||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | ||
# motors | 1 | 0 | 0.1 | 0.1 | 0.2 | 0.2 | 0.3 | 0.3 | 0.4 | 0.4 | 0.5 | 0.5 | 0.6 | 0.6 | 0.7 | 0.7 | 0.7 | 0.8 | 0.8 | 0.9 | 0.9 | 1 | 1 | 1.1 | 1.1 | 1.2 | 1.2 | 1.3 | 1.3 | 1.4 | 1.4 |
2 | 0.1 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.7 | 0.7 | 0.8 | 0.9 | 1 | 1.1 | 1.2 | 1.3 | 1.4 | 1.5 | 1.6 | 1.7 | 1.8 | 1.9 | 2 | 2.1 | 2.1 | 2.2 | 2.3 | 2.4 | 2.5 | 2.6 | 2.7 | 2.8 | |
3 | 0.1 | 0.3 | 0.4 | 0.6 | 0.7 | 0.8 | 1 | 1.1 | 1.3 | 1.4 | 1.5 | 1.7 | 1.8 | 2 | 2.1 | 2.2 | 2.4 | 2.5 | 2.7 | 2.8 | 2.9 | 3.1 | 3.2 | 3.4 | 3.5 | 3.6 | 3.8 | 3.9 | 4.1 | 4.2 | |
4 | 0.2 | 0.4 | 0.6 | 0.7 | 0.9 | 1.1 | 1.3 | 1.5 | 1.7 | 1.9 | 2.1 | 2.2 | 2.4 | 2.6 | 2.8 | 3 | 3.2 | 3.4 | 3.5 | 3.7 | 3.9 | 4.1 | 4.3 | 4.5 | 4.7 | 4.9 | 5 | 5.2 | 5.4 | 5.6 |
wire area: 1.0mm² | wire length [m.] | ||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | ||
# motors | 1 | 0 | 0.1 | 0.1 | 0.1 | 0.2 | 0.2 | 0.2 | 0.3 | 0.3 | 0.4 | 0.4 | 0.4 | 0.5 | 0.5 | 0.5 | 0.6 | 0.6 | 0.6 | 0.7 | 0.7 | 0.7 | 0.8 | 0.8 | 0.8 | 0.9 | 0.9 | 0.9 | 1 | 1 | 1.1 |
2 | 0.1 | 0.1 | 0.2 | 0.3 | 0.4 | 0.4 | 0.5 | 0.6 | 0.6 | 0.7 | 0.8 | 0.8 | 0.9 | 1 | 1.1 | 1.1 | 1.2 | 1.3 | 1.3 | 1.4 | 1.5 | 1.5 | 1.6 | 1.7 | 1.8 | 1.8 | 1.9 | 2 | 2 | 2.1 | |
3 | 0.1 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.7 | 0.8 | 0.9 | 1.1 | 1.2 | 1.3 | 1.4 | 1.5 | 1.6 | 1.7 | 1.8 | 1.9 | 2 | 2.1 | 2.2 | 2.3 | 2.4 | 2.5 | 2.6 | 2.7 | 2.8 | 2.9 | 3 | 3.2 | |
4 | 0.1 | 0.3 | 0.4 | 0.6 | 0.7 | 0.8 | 1 | 1.1 | 1.3 | 1.4 | 1.5 | 1.7 | 1.8 | 2 | 2.1 | 2.2 | 2.4 | 2.5 | 2.7 | 2.8 | 2.9 | 3.1 | 3.2 | 3.4 | 3.5 | 3.6 | 3.8 | 3.9 | 4.1 | 4.2 |
wire area: 1.5mm² | wire length [m.] | ||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | ||
# motors | 1 | 0 | 0 | 0.1 | 0.1 | 0.1 | 0.1 | 0.2 | 0.2 | 0.2 | 0.2 | 0.3 | 0.3 | 0.3 | 0.3 | 0.4 | 0.4 | 0.4 | 0.4 | 0.4 | 0.5 | 0.5 | 0.5 | 0.5 | 0.6 | 0.6 | 0.6 | 0.6 | 0.7 | 0.7 | 0.7 |
2 | 0 | 0.1 | 0.1 | 0.2 | 0.2 | 0.3 | 0.3 | 0.4 | 0.4 | 0.5 | 0.5 | 0.6 | 0.6 | 0.7 | 0.7 | 0.7 | 0.8 | 0.8 | 0.9 | 0.9 | 1 | 1 | 1.1 | 1.1 | 1.2 | 1.2 | 1.3 | 1.3 | 1.4 | 1.4 | |
3 | 0.1 | 0.1 | 0.2 | 0.3 | 0.4 | 0.4 | 0.5 | 0.6 | 0.6 | 0.7 | 0.8 | 0.8 | 0.9 | 1 | 1.1 | 1.1 | 1.2 | 1.3 | 1.3 | 1.4 | 1.5 | 1.5 | 1.6 | 1.7 | 1.8 | 1.8 | 1.9 | 2 | 2 | 2.1 | |
4 | 0.1 | 0.2 | 0.3 | 0.4 | 0.5 | 0.6 | 0.7 | 0.7 | 0.8 | 0.9 | 1 | 1.1 | 1.2 | 1.3 | 1.4 | 1.5 | 1.6 | 1.7 | 1.8 | 1.9 | 2 | 2.1 | 2.1 | 2.2 | 2.3 | 2.4 | 2.5 | 2.6 | 2.7 | 2.8 |
2.2.1
Take note of the polarity
to connect the motor wires on the terminal block.
2.2.2
Connect the wires from an individual or daisy-chained motor(s) to 1 or more terminal blocks
.
ATTENTION.
Watch out for the polarity.
Wrong connection may damage the power supply.
TIP.
Use good recognizable motor wiring.
E.g. red wire = plus (+) ; black wire = minus (-)
2.2.3
Mount the power supply back to the wall.
Put the terminal block(s) in place on the power supply.
TIP.
Do not connect unused terminal blocks.
2.2.4
Connect the power cable and make sure all cables are guided through the recess
on the power supply.
TIP.
Use cable ties to fasten all cables and wires using the cable management clamps
.
2.2.5
Mount the power supply back to the wall and connect the power cable to the power socket.
2.2.6
Flip the power switch to the ON
position.
Check if all group LEDs
are lit.
2.2.7
Install the front cover.
Check if all PowerView® blinds connected to the power supply can be controlled up and down
.
2.2.8
You are ready to use your PowerView® PS-18/300 power supply.
3. Technical data¶
Rated input voltage (VAC)
100-240
Rated input Frequency (Hz)
47-63
Rated output voltage (VDC)
18 ± 5%
Efficiency level
> 90% at full load
No load power (W)
< 6
Max. total current output (A)
16
Max. group current output (A)
4.0
Max. power output (W)
288
Output protection (per group)
fuse T6.3A/250V
Output holdup time (ms)
8.3
Operation temp. (°C)
-40…+50
Operation humidity (%)
20…85
Storage temp. (°C)
-40…+80
Storage humidity (%)
10…95
Operational lifetime (hrs)
> 100,000 @ 25°C
Material
Plastic ABS
Colour
white
Dimensions (l x w x h, mm)
223 x 195 x 51
Weight (kg)
0.98
Approvals
CE
Important notice
Hunter Douglas Europe B.V. and its affiliates (Hunter Douglas) reserve the right to make corrections, enhancements, improvements and other changes to its products and services, and to discontinue any product or service. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products (also referred to herein as "components") are sold subject to Hunter Douglas’ terms and conditions of sale supplied at the time of order acknowledgment. Hunter Douglas warrants performance of its components to the specifications applicable at the time of sale, in accordance with its standard warranty terms. Testing and other quality control techniques are used to the extent Hunter Douglas deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. Hunter Douglas assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products, applications and interfaces using Hunter Douglas components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. Hunter Douglas does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which Hunter Douglas components or services are used. Information published by Hunter Douglas regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from Hunter Douglas under the patents or other intellectual property of Hunter Douglas. Reproduction of Hunter Douglas information in Hunter Douglas data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Hunter Douglas is not responsible or liable for any altered documentation. Information of third parties may be subject to additional restrictions. Resale of Hunter Douglas components or services with statements different from or beyond the parameters stated by Hunter Douglas for that component or service voids all express and any implied warranties for the associated Hunter Douglas component or service and is an unfair and deceptive business practice. Hunter Douglas is not responsible or liable for any such statements. Buyers acknowledge and agree that they are solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of Hunter Douglas components in its applications, notwithstanding any applications-related information or support that may be provided by Hunter Douglas. Buyers represent and agree that they have all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyers fully indemnify Hunter Douglas and its representatives against any damages arising out of the use of any Hunter Douglas components in safety-critical applications. Manufacturer/Supplier address: Hunter Douglas Europe B.V, P.O. Box 5072 Piekstraat 2 3008 AB Rotterdam The Netherlands
document version: 1.0 | generated: 2021-03-05 00:13:25